Area of research
Mechanical Engineering · Aerospace Engineering
Research interest
Research interests include Aluminum Alloys Composites Properties, Aluminum Alloy Microstructure Properties, Magnesium Alloys: Properties and Applications, and Microstructure and mechanical properties.
Radiotherapy plus neoadjuvant and concomitant IL-13Rα2-directed immunotoxin therapy for diffuse intrinsic pontine glioma
MFS‐Unet: A Multi‐Path Vision Mamba Network for Precise Thyroid Nodule Segmentation
Deep learning-assisted spectral technology monitoring the preservation effect of sodium octenyl succinate starch co-loaded with cinnamaldehyde and carvacrol microcapsules for pork
Rapid desorption-induced multiscale structural alterations in gas-bearing coals from Sydney Basin: Implications for coal and gas outburst
Stability enhancement and parameter optimization of grid-forming converter control strategy considering overcurrent protection
Achieving superior strength-ductility balance by tailoring dislocation density and shearable GP zone of extruded Al-Cu-Li alloy
Enhancing strength-ductility synergy in an extruded Al-Cu-Li-Mg-Ag alloy via homogeneous GP zones and dislocation configuration
Unveiling the origin of severe hot cracking susceptibility in Al-Li alloys
Achieving refined microstructures and improved mechanical properties in a cup-shaped Mg-Gd-Y-Zr alloy casting by novel near-liquidus squeeze cast process
New insight into enhancing the comprehensive mechanical performance in non-stretched Al-Cu-Li-(Mg)-(Ag)-Mn-Zr alloys
Regulation of precipitation behavior among T1, S', and θ' phases in Al–Cu–Li-(Mg–Ag) alloys by optimizing Ag/Mg ratios
Enhanced strength and ductility in sand-cast Al-Li-Cu-Mg-Zr alloy via synergistic microalloying with Sc and Ti
Enhanced strength and ductility in sand-cast Al-Li-Cu-Mg-Zr alloy via synergistic microalloying with Sc and Ti
Microstructure evolution and mechanical properties of a cast and heat-treated Al–Li–Cu–Mg alloy: Effect of cooling rate during casting
Influence of Cu addition on hot tearing susceptibility and fluidity of Al-Li-Cu alloys: Experimental investigation, criterion prediction and simulation assessment
Microstructure and mechanical properties of repair welds of low-pressure sand-cast Mg–Y–RE–Zr alloy by tungsten inert gas welding
A comparative study on precipitation behavior of a sand-cast Al–Li–Cu alloy with the different quenching rates
Backstepping control for a two-link manipulator with appointed-time convergence
Variation in the microstructure and mechanical properties of permanent mold cast Al–3Li–2Mg–0.1Zr alloy with Zn addition
Retraction notice to “Development of curcumin-loaded silk fibroin nanoparticles as drug delivery vehicle for the treatment of ischemic stroke for patients in nursing care in hospitals” [J. Drug Deliv. Sci. Technol. 55 (2020) 101360]
Microstructure characteristics of an ultra-high strength extruded Al-4.7Cu–1Li-0.5Mg-0.1Zr–1Zn alloy during heat treatment
Formation of non-dendritic microstructures in preparation of semi-solid Mg-RE alloys slurries: Roles of RE content and cooling rate
Effect of Y and Gd content on the microstructure and mechanical properties of Mg–Y–RE alloys
High temperature mechanical behavior of low-pressure sand-cast Mg–Gd–Y–Zr magnesium alloy
Balance of mechanical properties of Mg-8Li-3Al-2Zn-0.5Y alloy by solution and low-temperature aging treatment
Effects of Mg and Sc additions on the microstructure, mechanical properties, and thermal stability of a cast Al-2Li-2Cu-0.2Zr alloy after thermal exposure
Microstructural characteristics and mechanical properties of extruded Al-4Cu-1Li-0.4Mg-0.1Zr-xZn alloy